ADAS Calibration Tulsa | 5 Things to Know

ADAS Calibration Tulsa

Windshield replacement typically involves a several-step process done by a technician:

1. Preparation:

   • The technician will cover your car’s interior to protect it from falling glass or debris.
   • They will then remove any components attached to the windshield, like wipers, rearview mirrors, and trim pieces.

2. Removing the Old Windshield:

   • A special tool called a cold knife is used to carefully cut through the urethane (adhesive) seal holding the old windshield in place.
   • The technician will then carefully remove the old windshield, often with the help of another person, to avoid damaging the surrounding bodywork.

3. Cleaning and Preparing the Installation Area:

   • The technician will meticulously clean the pinch weld (the metal frame where the windshield sits) to remove any old urethane, rust, or debris.
   • An adhesion promoter may be applied to the pinch weld to ensure a strong bond with the new urethane.

4. Installing the New Windshield:

   • The technician will apply a bead of urethane sealant around the perimeter of the pinch weld.
   • Carefully, they will position the new windshield into the opening and ensure proper alignment.
   • Suction cups or wedges might be used to hold the windshield in place while the urethane cures.

5. Curing and Finishing:

   • The car needs to sit for a specific time, typically several hours, to allow the urethane adhesive to cure completely.
   • Once cured, the technician will remove any temporary supports and reinstall the wipers, mirror, and trim pieces.
   • Some advanced windshields with driver assistance features may require recalibration by a qualified technician.

Thus, it’s essential to note that this is a general overview, and the specific steps may vary depending on the type of vehicle and the technician’s process. Consulting a professional for windshield replacement is recommended to ensure a safe and proper installation.

Windshield repair is a less invasive than replacement and can be completed in about 30-45 minutes.

Here’s a general breakdown of the steps involved:

1. Damage Assessment:
   • The technician will first assess the damage to ensure it meets the criteria for repair (typically cracks smaller than a quarter-inch and not in the driver’s line of sight).
2. Cleaning the Area:
   • The technician thoroughly cleans the area around the chip or crack to remove any dirt, debris, or moisture that could interfere with the repair process.
3. Resin Injection:
   • A small drill bit might be used to create a tiny entry point at the tip of any cracks to help the resin penetrate better.
   • A special injector is then used to fill the crack with a clear resin designed to bond with the glass.
   • A vacuum may be used to remove any air bubbles trapped within the crack.
4. Resin Curing:
   • Once the resin is injected, a UV lamp is used to cure the resin. This process hardens the resin and fills the crack, making it stronger and less visible.
5. Finishing Touches:
   • The technician will scrape off any excess resin from the windshield surface and polish the area for a smooth finish.
   • While the repair won’t make the damage completely disappear, it can significantly improve the clarity and structural integrity of the windshield.

Here are some additional things to keep in mind about windshield repair:

• Not all windshield damage can be repaired. If the crack is too large, deep, or in the driver’s direct line of sight, a replacement will likely be necessary.
• The success of a windshield repair depends on the skill of the technician and the severity of the damage.
• Windshield repairs are usually more affordable than replacements and can often be covered by insurance.

ADAS calibration is the process of ensuring the sensors in your car’s Advanced Driver-Assistance Systems (ADAS) are correctly aligned and pointed. Here’s a general overview of what ADAS calibration typically involves:

Preparation:

• The technician will first consult the manufacturer’s specifications for your specific vehicle model. This determines the calibration requirements and procedures.
• They will also check your car to ensure it meets certain pre-calibration conditions, such as:
  • Proper tire pressure
  • Correct wheel alignment
  • Full or near-full gas tank
  • No unnecessary weight in the car

Setting Up the Calibration Environment:

• Depending on the system being calibrated, this might involve setting up a special calibration frame with targets or reflectors in a controlled environment.
  • In some cases, the calibration can be performed on a clear, straight stretch of road with minimal traffic.

Calibration Procedure:

• Thus, the technician will use specialized diagnostic tools and software. Thus, to guide them through the calibration process specific to your car’s ADAS features.
  • This may involve electronically adjusting the sensors or cameras to ensure they are aimed correctly.
  • For camera-based systems, the calibration might involve driving the car at a specific speed to capture images of lane markings or other reference points.

Final Checks and Verification:

• Once the calibration procedure is complete, the technician will perform a final check of the ADAS systems. Thus, diagnostic tools are used to ensure everything is functioning correctly.
• They may also take you for a test drive to verify the proper operation of the ADAS features. Moreover, like automatic emergency braking or lane departure warning.

Important Points:

• ADAS calibration Tulsa is typically required after windshield replacement because the new glass can alter the position of the sensors mounted on it.
• Some ADAS systems may also require recalibration after certain repairs or if the sensors are bumped or misaligned.
• It’s important to consult a qualified technician with the proper tools and expertise to perform ADAS calibration. Improper calibration can compromise the effectiveness of your car’s safety features.

Note: The specific steps and requirements for ADAS calibration can vary depending on your car’s make, model, and year, as well as the particular ADAS features involved. Furthermore, it‘s always best to consult your vehicle’s owner’s manual or a certified technician for details regarding your car’s ADAS calibration procedures.